How to Measure Brake Pads to Order the Right Replacement

How to Measure Brake Pads

When you order replacement brake pads, getting the shape right matters more than anything else. Pads come in hundreds of shapes and sizes, and the only way to be sure you’re ordering the right one is to measure the pad you’ve taken out of your car. This guide shows you how to measure brake pads accurately, which four dimensions we need, and the extra details that help us identify your pad.

Why Your Car’s Make and Model Isn’t Enough

On a road car, the make and model usually points to one pad. On a competition car, it often doesn’t. Brakes get upgraded, calipers get swapped, and parts from one car end up on another. A Mini Cooper R50, for example, could be running BMW M3 calipers, so ordering pads for an R50 would get you the wrong shape entirely.

That’s why we ask for the measurements of the pad itself. The pad shows us what’s actually on your car now, even if the brakes have been changed since it left the factory.

What You’ll Need

  • The pad, removed from the caliper
  • A ruler, or ideally a vernier or digital caliper for more accurate readings
  • A phone camera
  • Our brake pad measurement sheet

Remove the Pad Before You Measure

You need the pad in your hand to measure it properly. Measuring through the caliper or wheel won’t give you accurate dimensions.

Removing pads varies by caliper, so follow the procedure for yours. Don’t press the brake pedal while the pads are out, since the caliper pistons can be pushed out of their bores. If you’re not confident removing pads yourself, have a mechanic do it.

The Four Measurements We Need

Measure everything in millimetres, and always measure the physical pad, not a drawing or a picture on screen. For each measurement, record the largest dimension. The letters below match our brake pad measurement sheet, so you can fill it in as you go.

A and B are measured on the backing plate, C on the friction material only, and D through both..

Brake Pad Measurements

A: Full Pad Width

Lay the pad with the friction material facing you and measure across the full width of the backing plate, at its widest part.

Brake Pad Width

B: Full Pad Height

Measure the full height of the pad from top to bottom, including any mounting ears or tabs on the backing plate. These ears are often what makes one pad shape different from another, so make sure they’re included.

Brake Pad Height

C: Pad Material Height

Measure the height of the friction material only, from its top edge to its bottom edge. Two pads can share a similar backing plate but carry different friction material shapes, so this helps us tell them apart.

Brake Pad Depth

D: Full Pad Thickness

Turn the pad on its side and measure from the rear of the backing plate to the friction face. This is the overall thickness: backing plate plus friction material together.

Brake Pad Thickness

If your pad is worn, the thickness you measure will be less than a new pad’s. That’s fine, just let us know the pad is used so we can allow for it. Width and height are what identify the shape.

Brake Pad Measurement Sheet

Tips for an Accurate Measurement

  • Measure each dimension twice. It takes seconds and catches mistakes.
  • Hold the ruler or vernier square to the pad, not at an angle.
  • If the inner and outer pads look different, measure both and tell us which is which.
  • Note anything unusual: wear sensors, clips, shims or cut-outs in the backing plate.

Photos to Send With Your Measurements

Measurements tell us the size; photos confirm the shape. Take a clear photo of both sides of the pad, the friction side and the backing plate side, with a ruler laid beside it so we can see the scale. Shoot it flat on, in good light, so the outline of the backing plate and any mounting ears is clear.

If photos are tricky, trace around the pad on a sheet of paper instead, marking any slots, mounting holes and ears, and send us a photo of the tracing.

Other Details That Help

Along with the measurements and photos, send us:

  • Your car’s make and model, plus any brake upgrades or changes you know about
  • The caliper make and model, if you know them; all calipers have a part number on the body
  • Any reference number printed or stamped on the pad’s backing plate

None of these replace the measurements, but together they help us confirm the right pad faster.

Sending Us Your Measurements

Once you’ve got your measurements and photos, fill in the form on our brake pad support page. Enter the four measurements, add your photos, and the Race and Rally team will help you find the right pads within 24 hours. From there we can help you choose a compound to suit how you use the car.

Final Thoughts

Measuring the pad you’ve taken off is the surest way to order the right replacement, especially on a competition car where the brakes may not match the car. Record the four dimensions, take clear photos of both sides with a ruler beside the pad, and send them over with your caliper details. Once we know the shape, we’ll help you pick the right pad from our brake pads range. After fitting, follow the correct bedding-in procedure.

vernier and brake pads

Frequently Asked Questions

Why can’t you identify my pads from the car model?

Because the brakes fitted may not be the ones the car left the factory with. Competition cars especially are often running calipers from a different car, so the pad itself is the only reliable reference.

Do I need to remove the pad to measure it?

Yes. You can’t get accurate dimensions with the pad still in the caliper, and we need the full shape, including the backing plate.

Is a ruler accurate enough?

A ruler works, but a vernier or digital caliper is more accurate, which helps when two pad shapes are only a few millimetres apart.

What if my inner and outer pads are different shapes?

Measure both, label which is which, and send photos of each. Some calipers use different inner and outer pads.

My pad is worn. Can I still measure it?

Yes. Width and height identify the shape, and they don’t change with wear. Just let us know the pad is used when you send the thickness.

Back to blog