Mocal Oil and Fuel System Parts
Mocal parts cover the plumbing that sits around your engine’s oil and fuel systems: relocating a filter, adding a temperature gauge, connecting an oil cooler or meeting fuel sampling rules. Here’s what to look for:
- Oil filter heads and sandwich plates, for relocating your oil filter or adding ports for an oil cooler and gauges
- M22 fittings, including a slimline high-flow banjo adaptor for tight spaces on top of an oil cooler
- Oil pressure switches to run a dash warning light
- An FIA fuel sampling kit, built for Motorsport UK, Motorsport Ireland and FIA events
- Roll over valves, tee fittings, silicone hose and rubber mounts to complete the install
Oil System Parts
|
Part |
What It’s For |
Key Specs |
|
Sandwich plate with temperature gauge port |
Adding ports between the oil filter and engine |
1/2" BSP ports, 3/4" UNF filter thread, 1/8" NPT temperature gauge port |
|
Billet remote oil filter head |
Relocating the oil filter where space is tight, or to make servicing easier |
M22 x 1.5 female ports, 3/4 UNF filter thread, suits spin-on filters 76 to 98mm in diameter, left-to-right or right-to-left flow, 2 x 1/8" NPTF take-offs |
|
M22 high-flow banjo adaptor, slimline |
Connecting to an oil cooler where there’s little room above it |
Male M22 x 1.5, -06, -08, -10 or -12, 26mm high to the top of the banjo bolt |
|
Low oil pressure switch sender |
Triggering a dash warning light |
1/8" x 27 NPT, 20 or 35 PSI |
The remote filter heads are popular for engine conversions and other modifications that leave little room for the filter. Their two 1/8" NPTF take-offs let you fit an oil temperature or pressure gauge or switch, with blanking plugs included for any you don’t use.
The slimline banjo adaptor and oil cooler rubber mounts are built for fitting an oil cooler. If you need the cooler itself, see our Setrab oil coolers.
Fuel System Parts
The FIA fuel sampling kit gives scrutineers a fast, safe way to take a fuel sample at Motorsport UK, Motorsport Ireland and FIA events. A tee adaptor breaks into your existing fuel line, connected to an FIA-approved Aeroquip FD90 dry break coupling and 2 metres of fuel hose. The smaller plug half stays on the car, while the socket half is stored until a sample is needed.
The in-line roll over valves were developed in response to FIA Appendix J, Article 258 for fuel cell ventilation. The valve closes if the tank tilts beyond 90°, uses an aluminium float ball to shut off fuel surging up the valve, and has a 200 millibar bypass to stop pressure building in the tank.
Frequently Asked Questions
What does an oil filter sandwich plate do?
A sandwich plate fits between the oil filter and the engine, giving you extra ports to run oil to a cooler or fit a temperature gauge without modifying the engine itself. Check the filter thread and port sizes on the product page match your engine and fittings.
Do I need a fuel sampling kit?
It depends on your series, but most speed events require it. Under both Motorsport Ireland and Motorsport UK rules, fuel-injected cars need an FIA-approved dry break coupling so a fuel sample can be taken, and you must carry a length of hose to connect to it. Motorsport Ireland asks for at least 600mm of hose and Motorsport UK at least 300mm, so the 2 metres of hose in Mocal’s kit covers both. Rules can change between seasons, so check your championship’s current regulations before your next event.
Which flow direction do I need for a remote oil filter head?
It depends on how your oil lines run. On a left-to-right head, oil enters on the left-hand side and leaves on the right. On a right-to-left head, it enters on the right and leaves on the left. Choose whichever lets your feed and return lines reach the head without tight bends or crossing over, so the plumbing stays as simple as possible.